Home > Raw Materials | Stains > USG Plasters and Information >

UNAVAILABLE - USG Statuary Hydrocal 50 Lbs.


U.S. Gypsum STATUARY HYDROCAL 50 lbs. Bag
U.S. Gypsum STATUARY HYDROCAL 50 lbs. Bag


 
Alternative Views:


U.S. Gypsum STATUARY HYDROCAL 50 lbs. Bag
Item Class Raw Materials


Product Code:
RMSTAHYD50
Qty:

Description
 
U.S. Gypsum Statuary HYDROCAL® Brand Gypsum Cement 50 lbs. Bag
STATUARY HYDROCAL is a basic HYDROCAL cement with a lower use consistency of about 40 lbs. of water per 100 lbs. of plaster. Extremely hard and strong with improved plasticity. Designed for solid and hollow art casting.
Please note: 100lb bags must be split and repackaged to be shipped UPS. Please expect an $18.00 Handling charge when ordering 100 lb bags shipped UPS.

—Produces harder and stronger casts than HYDROCAL® Brand White Gypsum Cement.
—Basic gypsum cement with excellent plasticity development.
—Recommended for both solid and hollow casting.
—Very white in color and can accept colorants easily.

Technical Properties English Metric
Use Consistency (parts of water by weight per 100 parts plaster ) 40 40
1 Hr. Compressive Strength 3,000 psi 6.9 MN/m2
Dry Compressive Strength 6,500 psi 44.8 MN/m2
Maximum Setting Expansion 0.250% 0.250%
Density Wet 113.0 lb/ft3 1.81 g/cm3
Dry 96.0 lb/ft3 1.54 g/cm3
Set Time (Machine Mix)* 25-35 min. 25-35 min.

General Directions and Guidelines
Preparing the Mix Use potable water at temperatures between 70 and 100 °F (21 and 38 °C). Since variations in slurry (Statuary HYDROCAL® Brand Gypsum Cement and water mixture) temperature produce variations in setting time, it is important to keep both Statuary HYDROCAL Brand Gypsum Cement and and water in a stable temperature environment prior to use. The higher the temperature of the slurry, the shorter the set time.

Measuring
Weigh both Statuary HYDROCAL Brand Gypsum Cement and water at the recommended use consistency for each mix (see technical
properties above). The water-to-Statuary HYDROCAL Brand Gypsum Cement ratio is critical because it governs all physical
properties of the final cast piece.

Soaking
Sift or strew Statuary HYDROCAL Brand Gypsum Cement into water slowly and evenly. Do not drop handfuls of Statuary HYDROCAL
Brand Gypsum Cement directly into the water. Allow soaking for 1-2 minutes. Statuary HYDROCAL Brand Gypsum Cement should
be fully dispersed in the water prior to mixing. Small batches require less soaking than large batches. See bulletin IG503 for
specific soaking instructions.

Mixing
Mixing the Statuary HYDROCAL Brand Gypsum Cement slurry is one of the most important steps in producing Statuary HYDROCAL Brand Gyspum Cement casts with maximum strength, hardness, and other important properties.
Mechanically mixed slurries develop uniform casts with optimal strengths. Statuary HYDROCAL Brand Gypsum Cement can be
mechanically mixed through both batch and continuous processes. Proper blade and bucket dimensions are important for
obtaining the best batch mix.

Pouring
To prevent air entrainment and provide a uniform, smooth surface, careful pouring of the slurry is necessary. Agitation of the
filled mold is a further step used to prevent air at or near the surface of the cast piece. Whenever possible, the slurry should be
poured carefully in the deepest area so the slurry flows evenly across the surface of the mold.
Pouring a large amount of slurry directly on the face of the mold may result in slight densification of the cast at the point
where the slurry strikes the surface of the mold.

Drying
All casts should be dried as quickly as is safely possible after manufacture so that maximum physical properties can develop.
Dry to a constant weight.
The best drying rooms or ovens provide (1) uniform and rapid circulation (minimum of 15-30 fps) of air with no “dead spots”
having little or no air movement, (2) equal temperatures throughout the entire area, and (3) provisions for exhausting a portion
of the air while replacing it with fresh air. High humidity surrounding the drying room or oven inhibits the efficiency of the drying
because the air pulled into the room is incapable of picking up much moisture from the cast pieces.
The maximum temperature at which Statuary HYDROCAL Brand Gypsum Cement casts are safe from calcination is 120 °F
(49 °C). With substantial free water in the cast piece, higher drying temperatures can be used without difficulty. As drying progresses, the temperature must be reduced to prevent calcination. Before removing casts from the dryer, the temperature should approach that of the area around the dryer to prevent thermal shock.

Storage
Keep in a dry, stable environment indoors. Do not stack more than 2 pallets high. Keep from drafts. Rotate stock.


Browse for more products in the same category as this item:

Raw Materials | Stains > USG Plasters and Information
Raw Materials | Stains