Home > Equipment > Clay Extruders > Bailey Pottery Wall Mount Clay Extruders >

Bailey Pottery 9" Standard Wall Mount Clay Extruder


Bailey Pottery 9" Standard Wall Mount Clay Extruder


 
List Price: $647.00
Our Price: $599.00
You save $48.00!

Price with Selected Options: $599.00
Item Class Clay Extruders



Product Code:
BPM500003

Bailey Extruder Dies

Bailey EBX DIE KIT M-500-024 for 9" Extruder: Large sized form dies. [Add $180.00]
Bailey Extruder Drive Upgrade

Bailey Extruders: Upgrade to Air Powered Drive (compressor not included) [Add $926.00]

Qty:  
Description
 

Bailey Pottery 9" Standard Wall Mount Clay Extruder


Bailey 9" Clay Extruder on sale at Sheffield PotteryThis is the largest wall mounted clay extruder on the market. It can extrude 8" hollow forms !
The Bailey clay extruder is sturdy and economical.
You can even add an air-powered compressor drive to make extruding large amounts of clay easy !

Bailey 9" extruder optional die setThe optional die kit M-500-024 (shown right : not included) creates large sized forms on Baltic Birch die plates .


OPTIONAL UPGRADE: Air Compressor Powered drive for Bailey Pottery Clay Extruders : (shown Right : Not included)

Bailey Optional Powered Extruder driveSystem 3 Power Drive Frame is designed for use with any System Barrel. The System 3 is powered by an air compressor (not included) and provides a constant uninterrupted flow of clay for the entire plunge of the barrel. Operated by a foot pedal, both hands are always free to control the form. This allows the operator the greatest amount of control in forming a shape. The air cylinder pivots up for fast easy reloading. This unit comes complete with pressure regulator, moisture trap, pressure gauge, and foot pedal.
Most extruding will require a setting on the Power Drive Extruder regulator of about 90 to 100 lbs of pressure to extrude forms through the dies. This means the actual compressor should have an auto "on/off" setting on it's regulator (built into the compressor) that supplies about 85 psi (when it goes on) to 125 psi (when it goes off). You do not want a compressor that comes on lower than 80 lbs pressure. You can have a supply that goes up to 150 psi.



The standard 9" Bailey Clay Extruder is designed to extrude medium to large sized clay forms up to 8” across. The barrel is permanently welded to the drive frame and cannot be changed. It is made of mild steel and should be cleaned and dried when not in use to minimize rust. The Plunger Arm assembly features an extra long handle and movable shackle for the best leverage while extruding. The wall-mounted clay extruder comes with wall mounting hardware, (1) 8” Clover die, (2) 11” x 13” Birch blank die plates, (1) 5” x 6” coil die and the Die Adapter.
Extrusion Range:
From Expansion Box: 4” – 8” hollow clay forms
With Die Adapter- Multiple solid clay coils (single small solid clay coils will not extrude well from this barrel due to the amount of clay the barrel holds- the 4" Barrel is recommended for single solid clay coils ), hollow tubes from 2" - 3" square or round.
Barrel Capacity: 29 lbs of clay (including Expansion Box)
Die Plate Dimensions: 5” x 6” (w/Die Adapter), 11” x 13”
Brace: Standard Die Brace (M-500-026), System Die Brace (M-500-027)
Recommended Die Kit: Standard Die Kit (w/Die Adapter) (M-500-023), EBX Die Kit (M-500-024)
Mounting Options: wall mount, Standard Table Mount (M-500-004)

Please note: not all clays are good for extruding:

Each 9" barrel comes with a stainless steel center die support. The support consists of a stainless steel pipe which spans horizontally inside the bottom of the 5" plunging section of the barrel. An eyebolt hangs from the center of the pipe and extends through a hole in the birch die in the center. Then a washer and wing nut is attached underneath the die. Two small stainless bolts (located either side of the 5" barrel) are tightened inward so they extend into the hollow of the stainless pipe and keep it in place. This stainless support prevents the center of the birch die from bending and breaking due to pressures from the clay being forced down from the plunge section of the barrel. You still use the "C-clamps" at 4 points at the perimeter of the die to clamp the exterior wood to the steel expansion box. This hanger support is only used with 6" and 8" large tubes. When it isn't necessary, remove it from the barrel by withdrawing the two small bolts sufficiently to remove the stainless pipe.



Browse for more products in the same category as this item:

Equipment > Clay Extruders > Bailey Pottery Wall Mount Clay Extruders
Equipment > Clay Extruders
Equipment